Antilag via cruise control! Custom code v6.9

Support is currently only for F-Series Gen 1 B48 & B58.

A catless downpipe is highly recommended to avoid clogging or damaging your vehicle.

This will retard timing a significant amount and build a lot of intake and exhaust pressure. We recommend infrequent use of antilag and to obey all local laws. By using this feature, you acknowledge and accept the risks, including, but not limited to:

• Additional stress on the car that may be damaging (engine, turbo, exhaust, etc.)

• Potential damage to your ear drum

• Starting fires

• Having too much fun

Works with manual or DCT transmissions, in any gear, with any driving mode (eco, comfort, sport, etc.) at any speed.

• Boost Pressure: Delta Actual

• Boost Pressure: Intake Manifold

• Boost Pressure: Pre-Throttle Body

• Boost Pressure: Target

• Custom Code: Antilag Status

• Custom Code: Antilag Stationary Maps

• Custom Code: Antilag Shutdown Reason

• Custom Code: Max Cooling Status

• Fuel: Lambda Actual

• Fuel: Lambda Target

• Fuel: Rail Pressure Actual

• Fuel: Rail Pressure Target

• Temperature: Exhaust Gas Before Turbine (EGT)

• Temperature: Air Intake (IAT)

To change the launch RPM for stationary antilag:

1. Stop the vehicle (below speed threshold to detect rolling).

2. Hold SHORT DOWN on the rocker for 2 seconds (engine light will blink) to enter the RPM setpoint configuration mode. This value is defaulted to mapped value (RPM setpoint) if you restart the car.

3. Tap or hold SHORT UP/DOWN on the rocker to increase/decrease the RPM shown on the tachometer.

4. Press RES button to accept the setting displayed RPM setpoint.

1. Stop the vehicle (below speed threshold to detect rolling).

2. Keep RPM below the setpoint

3. Hold FAR DOWN on the rocker for at least 1 second to enter antilag mode (engine light will blink quickly).

4. Press the throttle pedal beyond the mapped value (pedal position for activation) to have ignition cut, timing retarded and to start building boost as configured in the app.

5. Release FAR DOWN rocker switch when ready to launch (sit back first!).

1. Reach a steady speed (above threshold to detect rolling).

2. Select a lower gear to have the RPM within minimum and maximum bounds selected in app (3500 RPM is a good starting position with bounds set at 2500 RPM to 5000 RPM).

3. Hold FAR DOWN on the rocker for at least 1 second to enter antilag mode (engine light will blink quickly).

4. Press the throttle pedal beyond the mapped value (pedal position for activation) to have ignition cut, timing retarded and to start building boost as configured in the app.

5. Release FAR DOWN rocker switch when ready to launch (sit back first!).

• Pedal position for activation

• Speed threshold to detect rolling

• Rolling Options

  • Aggression

  • Boost setpoint

  • RPM minimum for rolling engagement

  • RPM maximum for rolling engagement

• Standing Options

  • Aggression

  • Boost setpoint

  • RPM setpoint

• Pedal position for activation

• Speed threshold to detect rolling

• Rolling Options

  • Ignition aggression (higher means more timing retard)

  • Lambda aggression (higher means richer)

  • Boost setpoint

  • Boost hysteresis (as a wastegate fader)

  • Ignition cut duration

  • RPM delay until cut

  • RPM minimum for rolling engagement

  • RPM maximum for rolling engagement

• Standing Options

  • Ignition aggression (higher means more timing retard)

  • Lambda aggression (higher means richer)

  • Boost setpoint

  • Boost hysteresis (as a wastegate fader)

  • Ignition cut duration

  • RPM delay until cut

  • RPM setpoint

• Safety Options

  • Emergency mode deceleration aggression

  • Coolant temperature minimum

  • Coolant temperature maximum

  • Exhaust gas temperature maximum

  • Intake air temperature maximum

  • Over boost limiter

Wastegate will be faded open as the target boost is approached (target boost - hysteresis) and fully open once reached or exceeded.

Safety shutdown (Emergency mode)
If any of the safety parameters are exceeded, the antilag function will end early and require the user to release the throttle before resuming regular operations. Antilag will be disabled until the safety margins are within bounds again and the user releases the throttle. Emergency mode temporarily enables “Limp Mode” to reduce exhaust gas temperatures (EGT) and relieve boost pressure (opens electronic wastegate).

You can log the parameter “Custom Code: Antilag Shutdown Reason”, or CC_ASR for short, to see the cause for the last shutdown event. Value resets to zero upon entering next antilag event.

Safety shutdown is engaged when:

• Engine coolant temperature (Tmot) is out of bounds: “Coolant temperature min” (CC_ASR bit 0) and “Coolant temperature max” (CC_ASR bit 1).

• Exhaust gas temperature (EGT) before turbo (Tabg_vl_xab) is greater than “Exhaust gas temperature max” (CC_ASR bit 2).

• Intake air temperature (tans_msg) is greater than “Intake air temperature max“ (CC_ASR bit 3)

• Intake manifold boost pressure (Ps) is greater than “Boost pressure setpoint” + “Over boost limiter“ (CC_ASR bit 4)