Page Comparison

## [v7.2]
## Added
- Motiv's Re|Flex support
	- Logging various channels including:
		- System status
		- Ethanol content
		- Low pressure fuel pressure
		- Ethanol PI scaling factor
		- PI DC raw
		- PI DC post factor
		- Aux1 Output DC
		- Aux2 Output DC
	- Limp mode when errors are detected:
		- If Reflex reports an error, or,
		- If ethanol sensor reports an error, or,
		- If no input from Reflex is detected in the last 10 seconds (15 second delay from engine start)
		- If low pressure fuel pressure drops below 3.0 bar (and a sensor is installed)
			- Custom Code DTC will appear in MG Flasher app
			- Check engine light will blink
			- Engine will not make any boost

## [v7.1.1 - v7.1.3]
## Changed
- Fixed missing burbles on certain software versions
- Fixed G-Series "failed to restore coding" bug
- Fixed exhaust flap control on Gen 1 Fxx Hybrids

## [v7.1]
## Added
- UniRocker and RockerCombo cruise control button configurations introduced:
	- UniRocker (Rocker Only):
		- Short up/down on the rocker:
			- Enter the CCM (hold position)
			- Enter sub-menu (hold position)
			- Confirm a selection (hold position)
		- Far up/down:
			- Navigate the menu (tap button)
			- Adjusts values (tap or hold button)
	- RockerCombo (Rocker and more):
		- RES and BC buttons:
			- Enter the CCM (hold button)
			- Enter sub-menu (tap button)
			- Confirm a selection (tap button)
		- Rocker button:
			- Short or far up/down:
				- Navigate the menu (tap button)
				- Adjusts values (tap or hold button)
- Custom Code Menu (CCM) added
	- New engine light (CEL) blink: different sub-menus blink a different number of times
	- Ability to enter "sub-menus" for each feature:
		- 0k RPM = Exit, cancel menu (slow blink)
		- 1k RPM = Switchable Map selection menu (1 blink)
		- 2k RPM = Burble selection menu (2 blinks)
		- 3k RPM = Max Cooling selection menu (3 blinks)
		- 4k RPM = Antilag RPM selection menu (4 blinks)
		- 5k RPM = Ethanol Content override selection menu (5 blinks)
		- 6k RPM = Exhaust Flap selection menu (6 blinks)
		- 7k RPM = Valet Mode (7 blinks)
- Ability to override ethanol content via CCM
	- Use tachometer to override E% anywhere between 0% (0 RPM) - 75% (7500 RPM)
	- This feature doesn't have any functionality other than demoing the ability to set a value (v7.3 will use it)
- Exhaust flap override control via CCM
	- Flap will be opened if exceeding max engine load (set via app: 50% - 200%)
	- Use tachometer to set flap functionality:
		- 0 RPM = OEM function
		- 1000 RPM = Closed flap
		- 2000 RPM = Open flap
- Valet mode toggle via CCM
	- Limited torque and engine RPM
	- Exceeding the set pedal position or vehicle speed will set a flag
		- The "Exceeded Value" flag will slow blink the CEL
		- Flag can be reset by disabling/enabling valet mode again
- [GEN 2] Radiator flap override control
	- When Max Cooling is enabled or Antilag is active, the front radiator flaps will open
	- In-app diagnostics allow flaps to open, close or use OEM settings until the vehicles is restarted

## Changed
- Long term storage of On-The-Fly feature settings:
	- Valet mode status (and exceeded values)
	- Exhaust flap status
	- Flex Fuel override status & value
- Safety protocol from switching into empty slots
	- Invalid selections will indicate via RPM at 7000

## [v7.0.6 - v7.0.8]
## Changed
- Fixed missing burbles on certain software versions
- Fixed Gen 1 Gxx "failed to restore coding" bug
- Fixed exhaust flap control on Gen 1 Fxx Hybrids
- Misc bug fix

## [v7.0.5]
## Changed
- Improved map switch method
- Improved antilag feature
	- Added ignition timing fading
	- Improved boost control (especially when stationary)
	- Improved RPM control with adjustable cylinder suppression
- [GEN 2] Max Cooling On-The-Fly will also control the radiator flap

## [v7.0.4]
## Added
 - Ability to read "Low Fuel Pressure" via 3rd byte in 0x0EC CAN bus ID
	- Fuel-it, or similar, kit required

## [v7.0.3]
## Changed
- Bug fix: Recognition of empty slots in custom tunes

## [v7.0.2]
## Changed
- Bug fix: Safety protocol from switching into empty slots

## [v7.0.1]
## Changed
- Resolved EEPROM saving bug from Custom Code v7.0
- Resolved "sticky" Antilag on select vehicles

## [v7.0]
## Added
 - Initial release for B48 Hybrid F-Series vehicles
 - Long term storage of On-The-Fly feature settings
	- Requires key cycle (set value, 5s ignition off, ignition on, saved)
	- Preserved between flashes, battery swaps, etc.
	- Switchable map slot selection
	- Burble aggression level
	- Max cooling status
	- Antilag standstill RPM setpoint
 - Logging of ethanol content from CAN sensor (ID 0x0EC)
## Changed
 - Safety protocol from switching into empty slots
	- Switchable Maps and Burbles OTF
	- Invalid selections will default to slot 0
 - Added engine status check