Tip |
---|
Custom Code v7.0.x (available with app version 370) bring Switchable Maps for all G-Series and F-Series software! |
Note |
---|
Custom Code v6.9.2 (outdated) has been released with App version 326! This update brings cruise control and BC button functions to Switchable Maps, Burbles, Max Cooling, and Antilag On-The-Fly (while the car is in motion)! |
Note |
---|
Custom Code v5.4 (outdated) allows to switch between OTS Octane and Ethanol blends map (up to E50) without the need to reflash the vehicle! Through a simple combination of the Brake Pedal, Accelerator Pedal, Traction Control Button and the Driver Select Switch you can quickly select between mapping. |
Info |
---|
Minimum/maximum OTS map version required to access Switchable Map option. Tuners should contact us about accessing Switchable Maps when using “Custom Flash Menu”. Custom Code v6.0+ and v7.0+:
Custom Code v5.4 (outdated):
|
Support is currently only for F-Series and G-Series Gen 1 B48H, B48 and B58.
...
Info |
---|
Instructions for using Switchable Maps On-The-Fly can be found here: Switchable Maps On-The-Fly |
Note |
---|
If you have Custom code v7.0.x or older, see instructions here: [Outdated] Configure Switchable Maps On-The-Fly |
...
Switchable Maps brings the ability to change between maps in real-time, without reflashing your car! This means you can change from a 91 OCT / 95 RON calibration to a 95 OCT / 102 RON with the press of a button by using your steering wheel controls or the in-app diagnostic menu!
...
Calibrations for 102 RON (95 OCT), 100 RON (94 OCT) and ACN 91 (for low quality 91 OCT / 95 RON) have been added to the list of choices when picking a file to flash. The octane level you select before flashing is the default (slot #0) map that is active after flashing. Slots 1 - 4 will contain either a lower/higher octane level, E30 or E40.
...
Expand | ||||
---|---|---|---|---|
Info | ||||
Minimum/maximum OTS map version required to access Switchable Map option. Tuners should contact us about accessing Switchable Maps when using “Custom Flash Menu”. Custom Code v6.0+ | (Current)||||
There is a ~10 second timeout which will cancel your selection if no buttons are pressed. If the selection menu times out, the map slot will not be adjusted and no changes will be saved. | ||||
Expand | ||||
title | and v7.0+:
Custom Code v5.4 ( | Outdatedoutdated) | ||
Driver Experience Switch and MSA Button.
In case your BMW does not have SPORT+ mode you will be limited to Slot #1, #2, #3 and reverting to Slot #0 is possible from SPORT mode by the same sequence - SPORT and 2 quick MSA presses Within the 5 seconds of holding the Gas Pedal at W.O.T position (while still holding the Brake Pedal) you will notice the RPM on the dash will reflect the choice you have selected (ie. 3000 RPM = Slot #3). Release the Brake and Gas Pedals fully to exit the selection process. RPM on the dash will return to actual engine RPM and the Check Engine Light will stop blinking. Now you can enjoy your newly selected map-set! | ||||
:
|
Support is currently only for Gen 1 B48H, B48 and B58.
...
Infographics
You can find infographics that visually describe the OTS map slot info here:
...
Switchable maps must be available and enabled in your software (selected during flashing process). Currently, only available on G-Series & F-Series Gen 1 B46/B48/B48H/B58. Gen 2 will be available soon.
Engine must be running (more than 30 seconds from start when using Custom Code v5.4 and earlier, Custom Code v6.0 can be used as soon as engine starts)
(Custom Code v5.4 and earlier) Vehicle must be at a standstill.
For users with Custom Tunes, please refer to the information on this page to gain access to this feature:
Custom Tuners - Map Pack Guide for Custom Code
Video (Outdated)
Watch our instructional video on YouTube to see how it works and read below for more info!
...